EXPERT ADVICE AND TIPS

How to prolong the lifespan of Diamond Turbo Saw blade

July 10th, 2023 4 minute read

The inevitable pain of having a quality diamond turbo saw blade is eventually having to replace it. Try to outrun the inevitable and hope you can get a few more cuts to be glad you saved a buck and eventually, the day will come when you won't be. However, there are ways to prolong the life of your blade. Perhaps the most important is sharpening your blade. It's important to make sure you're doing it the right way and taking all the necessary steps to optimize blade performance so that you can get the most out of your blades instead of trying to cut corners with a dull blade that leads to poor cuts and project failures.

5 Ways to Prolong Blade Life ↓Sharpening ↓Recap ↓FAQ ↓

What can I do to Prolong The Life of Diamond Turbo Saw Blades

1. Use the Right Blade for the Job

Let me say this again…Using the correct blade for the specific material you are cutting is crucial. Diamond turbo saw blades come in different sizes and configurations, each designed for specific applications. Using the wrong blade can lead to premature wear or even damage to the blade. Ensure that you choose a blade with the right diamond grit and bond for the material you are cutting.

2. Proper Cutting Technique

Using the proper cutting technique is essential for both the longevity of the blade and the efficiency of the cutting process. Apply consistent and even pressure throughout the cut, avoiding excessive force or side-to-side movement. Let the blade do the work and avoid forcing it through the material. Additionally, maintain a steady speed to prevent overheating, which can degrade the blade's performance. Put it this way, if your having to put muscle behind your cut, your cutting wrong.

3. Cooling and Lubrication

Heat is one of the major factors that can affect the lifespan of a diamond turbo saw blade. Adequate cooling and lubrication are crucial to dissipate heat and prevent blade overheating. Some blades have built-in cooling holes that allow water or coolant to flow over the cutting surface. Ensure that the blade remains properly cooled throughout the cutting process to extend its life and maintain cutting efficiency.

4. Avoid Cutting Hard Materials with an Exposed Blade

While diamond turbo saw blades are designed to cut through hard materials, it's best to avoid cutting extremely hard materials with an exposed blade whenever possible. Excessive contact with hard surfaces like metal or steel can cause the diamond segments to chip or wear out more quickly. If you need to cut hard materials, consider using a specialty blade with a protective layer or segment design that can handle the specific challenge.

5. Clean and Store Properly

After each use, it is crucial to clean your diamond turbo saw blade to remove any debris, resin, or buildup that can affect its performance. Use a brush or compressed air to remove particles from the blade's surface and ensure that the cutting edges remain clear. Once cleaned, store the blade properly in a dry and secure location. Avoid storing it in damp or humid environments, as this can lead to rust or deterioration.

Time for a new blade?

If your diamond segments are severely worn, it may be more cost-effective to replace the blade altogether.

Shop diamond blades

Prolonging Your Diamond Turbo Saw Blade via sharpening

There truly is no constructive way to sharpen a diamond turbo saw blade. Dressing stones and the lot aren't going to do a meaningful job of expanding the lifespan of your blade. The diamonds are going to wear down and eventually you will need a new blade. As stated at the top, you will just be outrunning the inevitable.

Remember, it's important to regularly inspect your diamond turbo saw blade for signs of wear or damage. If the blade has extensive damage or the diamond segments are severely worn, it may be more cost-effective to replace the blade altogether. Additionally, always prioritize safety by wearing appropriate protective gear and following the manufacturer's guidelines when sharpening or handling the blade.

It's important to remember that this isn't an MMA fight or a boxing match with your saw blade. Let the carefully engineered product do the cutting and just guide it through as it does its job. There's no need to apply excessive force. Keeping it steady and giving it a sensual, perfect touch is going to allow your blade to last longer and deliver beautiful quality cuts that are going to keep you happy in the long run as a blade owner.

TO RECAP…

To recap…

Yes for a third time, use the correct blade WITH the correct saw. Don't put “muscle” behind your cut- if your getting an arm workout while cutting…no good. No water might equal no saw blade. Make sure wet cutting has enough water to cool the blade. Clean your blade property to prolong life, it's a habit you have with your razor and all blades need this care. To find a quality diamond turbo saw blade, please check out the site!